Document control
Every drawing on the project, compared with the revision each board holds. Sheets doc control could not read are left for a person to check, never filled in.
Is this page current? All feeds OK
Doc control drawings
OK
51 min ago · expected every 24 h
By trade
| Trade | Sheets | Current | Newer rev waiting | Not held | Unreadable |
|---|---|---|---|---|---|
| COMM | 1 | 1 | 0 | 0 | 0 |
| CONC | 1 | 1 | 0 | 0 | 0 |
| EI | 2 | 2 | 0 | 0 | 0 |
| INSUL | 1 | 1 | 0 | 0 | 0 |
| MECH | 3 | 3 | 0 | 0 | 0 |
| MILL | 5 | 5 | 0 | 0 | 0 |
| PIPE | 4 | 4 | 0 | 0 | 0 |
| PMGT | 4 | 4 | 0 | 0 | 0 |
| QAQC | 3 | 3 | 0 | 0 | 0 |
| RIG | 2 | 2 | 0 | 0 | 0 |
| SCAF | 2 | 2 | 0 | 0 | 0 |
| SURV | 3 | 3 | 0 | 0 | 0 |
Source: drawing
Sheets needing action first
| Number | Title | Trade | Folder | Board holds | Doc control | Status |
|---|---|---|---|---|---|---|
| C-3700-01 | Press sole plate grout detail | CONC | DC/Concrete | AB | AB | CURRENT |
| CX-4000-01 | Startup, dry run and steam-up procedure | COMM | DC/Commissioning | 1 | 1 | CURRENT |
| E-3400-01 | Dryer section drive one-line | EI | DC/Electrical and Instrumentation | AB | AB | CURRENT |
| E-3410-01 | Instrument loop diagrams, dryer section | EI | DC/Electrical and Instrumentation | AB | AB | CURRENT |
| IN-3600-01 | Insulation details, steam and condensate | INSUL | DC/Insulation | AB | AB | CURRENT |
| M-3100-01 | Dryer section general arrangement | MILL | DC/Millwrights | AB | AB | CURRENT |
| M-3110-01 | Dryer bearing housing and journal details | MILL | DC/Millwrights | AB | AB | CURRENT |
| M-3120-01 | Gear train layout, bull and idler gears | MILL | DC/Millwrights | AB | AB | CURRENT |
| M-3130-01 | Felt run layout, top and bottom felts | MILL | DC/Millwrights | AB | AB | CURRENT |
| M-3140-02 | Blow box arrangement and supply ducts | MILL | DC/Millwrights | AB | AB | CURRENT |
| MB-3900-01 | Line bore and sleeve procedure, IB-1 to IB-5 | MECH | DC/Line Boring and Machining | C | C | CURRENT |
| MB-3900-02 | Idler bore sleeve detail | MECH | DC/Line Boring and Machining | AB | AB | CURRENT |
| MB-RPT-01 | Line bore report, IB-1 to IB-5 | MECH | DC/Line Boring and Machining | 0 | 0 | CURRENT |
| P-3300-ISO-01 | Steam joint and syphon isometric, D-01 to D-07 | PIPE | DC/Piping | AB | AB | CURRENT |
| P-3300-ISO-02 | Steam joint and syphon isometric, D-08 to D-14 | PIPE | DC/Piping | AB | AB | CURRENT |
| P-3300-ISO-05 | Condensate header replacement (CO-001) | PIPE | DC/Piping | AB | AB | CURRENT |
| P-PID-330 | Dryer steam and condensate P&ID | PIPE | DC/Piping | AB | AB | CURRENT |
| PM-CLOSE-01 | Final cost report and lessons learned | PMGT | DC/Project Management and Procurement | 0 | 0 | CURRENT |
| PM-OUT-01 | Outage execution plan | PMGT | DC/Project Management and Procurement | 3 | 3 | CURRENT |
| PM-OUT-02 | Outage lift and crane plan summary | PMGT | DC/Project Management and Procurement | 2 | 2 | CURRENT |
| QA-ITP-01 | Inspection and test plan, mechanical install | QAQC | DC/Welding and QA/QC | 2 | 2 | CURRENT |
| QA-ITP-02 | Hydro test procedure, dryers and steam joints | QAQC | DC/Welding and QA/QC | 1 | 1 | CURRENT |
| QA-RPT-01 | Hydro test and inspection records, dryers and steam joints | QAQC | DC/Welding and QA/QC | 0 | 0 | CURRENT |
| RIG-3200-01 | Mobile crane set-up, north pad and roof hatch | RIG | DC/Rigging and Heavy Lift | AB | AB | CURRENT |
| RIG-3200-02 | Machine room crane rigging arrangement, dryers | RIG | DC/Rigging and Heavy Lift | AB | AB | CURRENT |
| S-3500-01 | Outage scaffold layout, tending side | SCAF | DC/Scaffolding | AB | AB | CURRENT |
| S-3500-02 | Outage scaffold layout, drive side and gear case | SCAF | DC/Scaffolding | AB | AB | CURRENT |
| SV-3800-01 | Machine centerline and survey control | SURV | DC/Survey and Layout | AB | AB | CURRENT |
| SV-3800-02 | Frame survey after removal | SURV | DC/Survey and Layout | AB | AB | CURRENT |
| SV-RPT-01 | Final alignment survey report, press and dryers | SURV | DC/Survey and Layout | 0 | 0 | CURRENT |
| TO-PKG-01 | Turnover package index, PM3 rebuild | PMGT | DC/Project Management and Procurement | 0 | 0 | CURRENT |
Source: drawing